<br><br><div class="gmail_quote">On Tue, May 24, 2011 at 2:53 PM, Chuck Young <span dir="ltr"><<a href="mailto:wylie1066@gmail.com">wylie1066@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
<div><div></div><div class="h5"><br><br><div class="gmail_quote">On Tue, May 24, 2011 at 12:26 PM, Mars Sjoden <span dir="ltr"><<a href="mailto:aurorageomatics@gmail.com" target="_blank">aurorageomatics@gmail.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
<div><div></div><div>On Tue, May 24, 2011 at 12:16 PM, Chuck Young <span dir="ltr"><<a href="mailto:wylie1066@gmail.com" target="_blank">wylie1066@gmail.com</a>></span> wrote:<br><div class="gmail_quote">
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">

<br>
I have a question related to the projection: <br><br>I have started 
with a layer set to the above projection.  Its metadata shows that it is
 set to the NAD83 / UTM 12 projection by displaying the same details 
"+proj=utm +zone=12 +ellps=GRS80 +datum=NAD83 +units=m +no_defs" .  I 
have created a new vector layer using the same projection and digitized 
the vector layer data over the current layer.  Then checked to be sure 
the new layer did in face assume the correct projection. <br>
<br>
After this I have loaded the new layer over a layer that was created 
earlier in the same projection, digitized over the same base layer and 
showing the same metadata, and they don't match up.  When I load the two
 together then do the zoom extents the map goes to extreme separation of
 the two layers.  <br>
<br>
I have tried to re-project one layer but as they are on the same projection already they don't change. <br><br>Why can the files become so different when they are all digitized over the same base layer at the same projection?<br>


<font color="#888888">
<br>Chuck</font><br></blockquote></div><br></div></div>Just a stab in the dark.<br><br>What was the projection of the Map Display when these layers were edited?  <br>Was "On the Fly reprojection" ON while these layers were edited?<br>


<br>There maybe a transformation error in datums perhaps?<br><font color="#888888"><br>mars<br>
</font></blockquote></div><br><br></div></div>Mars:  I have sent sample files to Giovanni for his review.  Possibly you would look at the same files.  I noticed the Extents data were different.  Seems as the two files were on Lat Lon and the other [STR] was on some State Plane coordinate system even though they both had NAD83 / UTM Zone 12 as their projection.<br>

<br>The Project Properties CRS was set to the default WGS84 at the time these files were created. (I didn't realize that.)  I had the Options CRS "Default CRS" set to "Global Defaulu Displayed Below will be used." And had the def for NAD83 / UMT Zone 12 set there as "+proj=utm +zone=12 +ellps=GRS80 +datum=NAD83 +units=m +no_defs"  which is the def for Zone 12.  <br>

<br>I suppose that could have created some confusion.<br><br>Is there any way to reset the ref from the one you will se in the Extents of the STR file to the one in the other two files?<br><br>If so it would make things a lot easier.<br>

<br>Thanks<br><font color="#888888"><br>Chuck<br><br></font></blockquote><div><br>Hmmm, you may be able to triangulate the Highways to the extent you know of... <br><br><br><ul><li>Try simply reseting the CRS (not reproject) of your Highways/FSR to WGS 84.</li>
<li>Set the Map to UTM 12 For projection</li><li>Set On reproject on the fly transformations</li><li>Your Highways and FSR should display near your STR shapefile now...  </li><li>May have to move your shapefiles to properly align if resolution limited information.</li>
<li>Reproject to desired projeciton</li></ul><br><br>Here are the files you sent me reprojected using these steps.<br><br>mars<br></div></div><br>