<div dir="ltr"><p dir="ltr"></p>
<p dir="ltr">On 12 Oct 2016 11:56 PM, "Carlos Cerdán" <<a href="mailto:sig.upagu@gmail.com" target="_blank">sig.upagu@gmail.com</a>> wrote:<br>
><br>
> AFAIK, It also is needed to turn off "on the fly SRC transformation" to get correct area values.... Or QGIS has fixed this point?</p>
<p dir="ltr">Everything should be fixed in recent versions, and I very (VERY) much want to know if any issues are still encountered.</p><p>Calculating area/length is a core task for a GIS and we need to make sure it's rock solid. (Which it should be since 2.16!)</p><p>Nyall<br></p><p dir="ltr"><br>
><br>
> If you can't get correct area values, check out about it....<br>
><br>
><br>
> 2016-10-12 7:40 GMT-05:00 DelazJ <<a href="mailto:delazj@gmail.com" target="_blank">delazj@gmail.com</a>>:<br>
>><br>
>> Hi,<br>
>> To complete Nicolas answer, you should check what are the measurements options set in Project --> Project Properties --> General tab.<br>
>> See also <a href="http://docs.qgis.org/2.14/en/docs/user_manual/introduction/general_tools.html#measuring" target="_blank">http://docs.qgis.org/2.14/en/<wbr>docs/user_manual/introduction/<wbr>general_tools.html#measuring</a><br>
>><br>
>> 2016-10-12 14:07 GMT+02:00 Nicolas Cadieux <<a href="mailto:nicolas.cadieux@archeotec.ca" target="_blank">nicolas.cadieux@archeotec.ca</a>><wbr>:<br>
>>><br>
>>> Hi,<br>
>>> You may be calculating square degrees and not metres.  It can depend on the crs depending on the tools you are using.<br>
>>> Nicolas<br>
>>><br>
>>> Le 11 oct. 2016 à 08:54, Martina Schäfer [via OSGeo.org] <[hidden email]> a écrit :<br>
>>><br>
>>>> I experienced some confusion with calculation of area using the field calculator in QGIS version 2.16.3. Since I'm using MapInfo Professional as well, I mainly use tab-files that I can open in both programmes, but occasionally I save as shapefile since this used to be the default in QGIS. <br>
>>>><br>
>>>> When comparing files, I coincidently realized that there was a mismatch in calculated area for the shapefile and the tab-file for exactly the same polygons! I used the field calculator in the attribute table in both cases, but for the shapefile the resulting areas were almost doubled in area compared to the tab-file. Any idea why this is happening? <br>
>>>><br>
>>>> I also realized similar differences when calculating area in a file where projection has been converted from SWEREF99TM (a Swedish national projection) to WGS84. There differences occurred in both the tab and shapefile compared to the area calculated for the same tab-file in MapInfo. Again I find this very confusing! <br>
>>>><br>
>>>> I need to rely on the area-calculations thus I really hope someone here can explain to me what is happening! <br>
>>>><br>
>>>> Thanks in advance, <br>
>>>> Martina <br>
>>>><br>
>>>><br>
>>>><br>
>>>><br>
>>>> ______________________________<wbr>__<br>
>>>> If you reply to this email, your message will be added to the discussion below:<br>
>>>> <a href="http://osgeo-org.1560.x6.nabble.com/inconsistenty-when-calculating-area-depending-on-file-type-or-projection-tp5290228.html" target="_blank">http://osgeo-org.1560.x6.<wbr>nabble.com/inconsistenty-when-<wbr>calculating-area-depending-on-<wbr>file-type-or-projection-<wbr>tp5290228.html</a><br>
>>>> To start a new topic under Quantum GIS - User, email [hidden email] <br>
>>>> To unsubscribe from Quantum GIS - User, click here.<br>
>>>> NAML<br>
>>><br>
>>><br>
>>> ______________________________<wbr>__<br>
>>> View this message in context: Re: inconsistenty when calculating area depending on file type or projection?<br>
>>> Sent from the Quantum GIS - User mailing list archive at Nabble.com.<br>
>>><br>
>>> ______________________________<wbr>_________________<br>
>>> Qgis-user mailing list<br>
>>> <a href="mailto:Qgis-user@lists.osgeo.org" target="_blank">Qgis-user@lists.osgeo.org</a><br>
>>> List info: <a href="http://lists.osgeo.org/mailman/listinfo/qgis-user" target="_blank">http://lists.osgeo.org/<wbr>mailman/listinfo/qgis-user</a><br>
>>> Unsubscribe: <a href="http://lists.osgeo.org/mailman/listinfo/qgis-user" target="_blank">http://lists.osgeo.org/<wbr>mailman/listinfo/qgis-user</a><br>
>><br>
>><br>
>><br>
>> ______________________________<wbr>_________________<br>
>> Qgis-user mailing list<br>
>> <a href="mailto:Qgis-user@lists.osgeo.org" target="_blank">Qgis-user@lists.osgeo.org</a><br>
>> List info: <a href="http://lists.osgeo.org/mailman/listinfo/qgis-user" target="_blank">http://lists.osgeo.org/<wbr>mailman/listinfo/qgis-user</a><br>
>> Unsubscribe: <a href="http://lists.osgeo.org/mailman/listinfo/qgis-user" target="_blank">http://lists.osgeo.org/<wbr>mailman/listinfo/qgis-user</a><br>
><br>
><br>
><br>
> ______________________________<wbr>_________________<br>
> Qgis-user mailing list<br>
> <a href="mailto:Qgis-user@lists.osgeo.org" target="_blank">Qgis-user@lists.osgeo.org</a><br>
> List info: <a href="http://lists.osgeo.org/mailman/listinfo/qgis-user" target="_blank">http://lists.osgeo.org/<wbr>mailman/listinfo/qgis-user</a><br>
> Unsubscribe: <a href="http://lists.osgeo.org/mailman/listinfo/qgis-user" target="_blank">http://lists.osgeo.org/<wbr>mailman/listinfo/qgis-user</a><br></p>
</div>