<html><body><div style="color: rgb(33, 33, 33); background-color: rgb(255, 255, 255);" dir="auto">Sam,</div><div style="color: rgb(33, 33, 33); background-color: rgb(255, 255, 255);" dir="auto"><br></div><div style="color: rgb(33, 33, 33); background-color: rgb(255, 255, 255);" dir="auto">Sorry it's U-Center not U-Control.</div><div id="mail-editor-reference-message-container" dir="auto"><br><hr style="display:inline-block;width:98%" tabindex="-1"><div id="divRplyFwdMsg" style="font-size: 11pt;"><strong>From:</strong> Scott Harrison <scott@sharrison.net><br><strong>Sent:</strong> Thursday, August 25, 2022, 8:01 AM<br><strong>To:</strong> Open Source GPS-related discussion and support <foss-gps@lists.osgeo.org><br><strong>Subject:</strong> Re: [FOSS-GPS] rtklib not outputting any solution<br></div><br><div style="color: rgb(33, 33, 33); background-color: rgb(255, 255, 255);" dir="auto">It's been a long while, and this is just a guess, but check your UBlox U-Contol app to make sure your chip is setup correctly for output.</div><div style="color: rgb(33, 33, 33); background-color: rgb(255, 255, 255);" dir="auto"><br></div><div style="color: rgb(33, 33, 33); background-color: rgb(255, 255, 255);" dir="auto">Good luck.</div><div id="mail-editor-reference-message-container" dir="auto"><br><hr style="display:inline-block;width:98%" tabindex="-1"><div id="divRplyFwdMsg" style="font-size: 11pt;"><strong>From:</strong> FOSS-GPS <foss-gps-bounces@lists.osgeo.org> on behalf of sam@samthurtle.com.au <sam@samthurtle.com.au><br><strong>Sent:</strong> Thursday, August 25, 2022, 5:23 AM<br><strong>To:</strong> foss-gps@lists.osgeo.org <foss-gps@lists.osgeo.org><br><strong>Subject:</strong> [FOSS-GPS] rtklib not outputting any solution<br></div><br>Hello members of the FOSS-GPS mailing list.
My name is Sam. It is nice to e-meet you all, and I hope you can help me
with an rtklib issue I am experiencing.
I have a U-blox NEO-M8P GPS receiver board connected via serial to my
NVIDIA Jetson running Ubuntu 18.04.
I am trying to use rtklib-qt to apply RTK corrections via NTRIP and
output a log file with the corrected solution. When I output the log
file for the solution, it outputs an empty file.
If I output the raw GPS in NMEA, I can see the pre-corrected stream is
output as expected.
If I output the correction stream in NMEA, I can see the corrections are
being output as expected.
It is also worth mentioning that I was not able to get the solution
results panel on the left of the main rtknavi window to display any
data. It just shows "Solution: ----" and lat/long/height 0.
Has anybody experienced this before, and perhaps able to offer any
advice?
I have also tested using rtklib 2.4.3 b34 on a Windows computer and I'm
experiencing the same issue, so I expect it's more than likely a setup
issue rather than a bug.
Please also see below some screenshots which may help in determining my
issue. Thanks in advance.
Input window:
See attached 1_input_window.png.
Rover options:
See attached 2_input_window_rover_options.png.
Correction options (obfuscated for security, duh)
See attached 3_input_window_correction_options.png.
Output streams:
See attached 4_output_streams.png.
(I tried to output the solution as both Lat/Long/Height and NMEA0183).
Log outputs:
See attached 5_log_outputs.png.
Kind regards,
Sam<br></div><br></div></body></html>